Do you want resetter epson series t20e, c90, c58 or Manual resetter for Canon Printer or drivers for vga, soundcard, ethernet, mainboard, etc. This is the right place to start
Saturday 14 February 2009
Subscribe to:
Post Comments (Atom)
skip to main |
skip to sidebar
cewek seksi
This blog contains manual resetter for epson, canon, hp, lexmark, also have free download drivers, free update antivirus such as symantec, avg, etc. Also has information hardware new product epson t20e
pusing yah! mampir kesini dulu lah
Abg seksi
cewek seksi
wants something hot's, search below
Hot Topics
Resetter Epson T20e
Printer Epson t20e is a new models from epson, this printer more suitable, smooth prints, goods colours, and more faster than inkjet epson older type, such as stylus c90, c58.
The problem is we still cannot find free resetter for this epson t20e type. but if we still want to download resetter for epson t20e
Printer Epson t20e is a new models from epson, this printer more suitable, smooth prints, goods colours, and more faster than inkjet epson older type, such as stylus c90, c58.
The problem is we still cannot find free resetter for this epson t20e type. but if we still want to download resetter for epson t20e
MAU TAHU GAK !!!
When we start our computer, sometimes we felt they too slow to appear the menu (tampilnya lama gitu lho). So we can use Registry Editor to fix it.
Followers
Blog Archive
Visitors
How to reset using manual resetter
Canon PIXMA iP1500
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
step 2 : Software for Permanant
1. Reconnect the printer cable.
2.Open General Tools software and select (
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode Pls use software for permanent reset"
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
+++++++++
Canon S900, S820, S750, S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.
CAN YOU FIX YOUR OWN HARD DRIVE
I can !!!
If we have a bad sector hard drive, we still can used it. how ? if we have software (freeware software) mhdd (you can download it at http://www.mhdd.com/).
1. we must boot from DOS (we can have it on cd win98 setup)
2. after we have C:> then we type mhdd (C:> mhhdd) and then press enter
3. after we allready inside mhdd we detect the hard drive first by pressing F2, than we check it by pressing F4. while checking we can see through where the broken drive or bad sector.
4. if we know where the position of bad sector is, we just type erase (still on mhhd) we just have to fill where we want to start to erasing then fill where we have to stop erasing.
5. after this step done, we go back check that drive by pressing F4 and then F4. If our hard drive not physically damage, I'm sure that hard drive allready fix it.
Note :
if we have any important's document on hard drive that we want to repair, we have to back up them first, because if doesn't they will lost for good.
If we have a bad sector hard drive, we still can used it. how ? if we have software (freeware software) mhdd (you can download it at http://www.mhdd.com/).
1. we must boot from DOS (we can have it on cd win98 setup)
2. after we have C:> then we type mhdd (C:> mhhdd) and then press enter
3. after we allready inside mhdd we detect the hard drive first by pressing F2, than we check it by pressing F4. while checking we can see through where the broken drive or bad sector.
4. if we know where the position of bad sector is, we just type erase (still on mhhd) we just have to fill where we want to start to erasing then fill where we have to stop erasing.
5. after this step done, we go back check that drive by pressing F4 and then F4. If our hard drive not physically damage, I'm sure that hard drive allready fix it.
Note :
if we have any important's document on hard drive that we want to repair, we have to back up them first, because if doesn't they will lost for good.
Tips and Tricks
You know!!! some times our computer suddenly just not function, they hang, they just can load OS, they just can appear on monitor.
If you also ever heard or even thats happen to your computers, don't be panic, don't be headaches, just read this tips belows.
Some times what makes that happen is because dirty. We are too lazy to clean our computers, so dust every where.
first, try to clean every elements inside the computers, such as Dimm (SDRam, DDram, RDRam) depend whats in your computer, soundcard (if not onboard), VGACard, and processor (becareful when you loose them) place them on save places. second try to brush them with alcohol (60-70%) using toothbrush (smooth). Third, let them dry. and then when you are sure they allready dry, then you put them back again to their place. after that, you can try to turn on your computers. Mostly this is work.
If you also ever heard or even thats happen to your computers, don't be panic, don't be headaches, just read this tips belows.
Some times what makes that happen is because dirty. We are too lazy to clean our computers, so dust every where.
first, try to clean every elements inside the computers, such as Dimm (SDRam, DDram, RDRam) depend whats in your computer, soundcard (if not onboard), VGACard, and processor (becareful when you loose them) place them on save places. second try to brush them with alcohol (60-70%) using toothbrush (smooth). Third, let them dry. and then when you are sure they allready dry, then you put them back again to their place. after that, you can try to turn on your computers. Mostly this is work.
No comments:
Post a Comment